View OP200_110687.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a
FEATURES Low Input Offset Voltage: 75 V Max Low Offset Voltage Drift, Over -55 C < TA < +125 C: 0.5 V/ C Max Low Supply Current (Per Amplifier): 725 mA Max High Open-Loop Gain: 5000 V/mV Min Low Input Bias Current: 2 nA Max Low Noise Voltage Density: 11 nV//Hz at 1 kHz Stable with Large Capacitive Loads: 10 nF Typ Pin Compatible to OP221, MC1458, and LT1013 with Improved Performance Available in Die Form GENERAL DESCRIPTION
Dual Low Offset, Low Power Operational Amplifier OP200
PIN CONNECTIONS 16-Pin SOIC (S-Suffix)
+IN A 2 NC 3 V- 4 NC 5 +IN B 6
The OP200 is the first monolithic dual operational amplifier to offer OP77 type precision performance. Available in the industry standard 8-pin pinout, the OP200 combines precision performance with the space and cost savings offered by a dual amplifier. The OP200 features an extremely low input offset voltage of less than 75 mV with a drift below 0.5 mV/C, guaranteed over the full military temperature range. Open-loop gain of the OP200 exceeds 5,000,000 into a 10 kW load; input bias current is under 2 nA; CMR is over 120 dB and PSRR below 1.8 mV/V. On-chip zenerzap trimming is used to achieve the extremely low input offset voltage of the OP200 and eliminates the need for offset pulling. Power consumption of the OP200 is very low, with each amplifier drawing less than 725 mA of supply current. The total current drawn by the dual OP200 is less than one-half that of a single OP07, yet the OP200 offers significant improvements over this industry standard op amp. The voltage noise density of the OP200, 11 nV//Hz at 1 kHz, is half that of most competitive devices. The OP200 is pin compatible with the OP221, LM158, MC1458/1558, and LT1013.
NC 8
NC = NO CONNECT
EPOXY MINI-DIP (P-Suffix), 8-Pin Hermetic DIP (Z-Suffix)
OUT A 1 -IN A 2 +IN A 3 V- 4 A -+ B +-
The OP200 is an ideal choice for applications requiring multiple precision op amps and where low power consumption is critical. For a quad precision op amp, see the OP400.
V+
BIAS
VOLTAGE LIMITING NETWORK +IN -IN
REV. A
Figure 1. Simplified Schematic (One of two amplifiers is shown.)
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2002
-
-IN B 7
-
15 14 13 12 11
-IN A 1
16
OUT A NC NC V+ NC NC OUT B NC
+ +
10 9
8 7 6 5
V+ OUT B -IN B +IN B
OUT
V-
OP200-SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Parameter Input Offset Voltage Long Term Input Voltage Stability Input Offset Current IOS Input Bias Current Input Noise Voltage Input Noise Voltage Density1 IB en p-p en VCM = 0 V VCM = 0 V 0.1 Hz to 10 Hz fO = 10 Hz fO = 1000 Hz 0.1 Hz to 10 Hz fO = 10 Hz Symbol VOS Conditions
(VS = 15 V, TA = 25 C, unless otherwise noted.)
OP200A/E Min Typ Max 25 0.1 0.05 0.1 0.5 22 11 15 0.4 10 125 36 18 1.0 2.0 75 Min OP200F Typ Max 50 0.1 0.05 0.1 0.5 22 11 15 0.4 10 125 3000 1500 7000 3200 3000 1500 36 18 2.0 4.0 150 Min OP200G Typ Max 80 0.1 0.05 0.1 0.5 22 11 15 0.4 10 125 7000 3200 3.5 5.0 200 Unit mV mV/mo nA nA mVp-p nV/ Hz pAp-p pA/ Hz MW GW
Input Noise Current in p-p Input Noise Current Density Input Resistance Differential Mode Input Resistance Common Mode Large Signal Voltage Gain in RIN RINCM AVO
VO - 10 V RL = 10 kW RL = 2 kW
5000 2000
12000 3700
M/mV
NOTES 1 Sample tested 2 Guaranteed but not 100% tested 3 Guaranteed by CMR test
-2-
REV. A
OP200 ELECTRICAL CHARACTERISTICS (V = 15 V, -55 C T +125 C for OP200A, unless otherwise noted.)
S A
Parameter Input Offset Voltage Average Input Offset Voltage Drift Input Offset Current Input Bias Current Large Signal Voltage Gain
Symbol VOS TCVOS IOS IB AVO
Conditions
Min
OP200A Typ 45 0.2
Max 125 0.5 2.5 5.0
Unit mV mV/C nA nA V/mV V/mV V dB mV/V V V
VCM = 0 V VCM = 0 V VO = 10 V RL = 10 W RL = 2 kW VCM = 12 V VS = +3 V to +18 V RL = 10 kW RL = 2 kW No Load AV = +1 12 11 3000 1000 12 115
0.15 0.9 9000 2700 12.5 130 0.2 12.4 12 600 8
Input Voltage Range* Common-Mode Rejection Power Supply Rejection Ratio Output Voltage Swing Supply Current Per Amplifier Capacitive Load Stability
NOTE *Guaranteed by CMR test.
IVR CMR PSRR VO ISY
3.2
775
mA nF
ELECTRICAL CHARACTERISTICS (V =
S
15 V, TA = 25 C, unless otherwise noted.)
Min 12 115 1.8 12 11 725 0.1 OP200F Typ Max 13 135 0.4 12.6 12.2 570 0.15 500 123 145 3.2 10 123 725 0.1 3.2 12 11 Min 12 110 OP200G Typ Max 13 130 0.6 12.6 12.2 570 0.15 500 145 3.2 10 725 5.6 Unit V dB mV/V V V mA V/mS kHz dB pF nF
Parameter
3
Symbol
Conditions
OP200A/E Min Typ Max 12 13 135 0.4 12 11 12.6 12.2 570 0.1 0.15 500 123 145 3.2
Input Voltage Range IVR Common-Mode Rejection Power Supply Rejection Ratio Output Voltage Swing Supply Current Per Amplifier Slew Rate Gain Bandwidth Product Channel Separation2 CS Input Capacitance Capacitive Load Stability
NOTES 1 Sample tested 2 Guaranteed but not 100% tested 3 Guaranteed by CMR test
CMR PSRR VO
VCM = 12 V VS = 3 V to 18 V RL= 10 kW RL = 2 kW No Load
120
ISY SR GBWP
AV = 1 VO = 20 Vp-p fO = 10 Hz AV = 1 No Oscillations
CIN
10
REV. A
-3-
OP200-SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (V = 15 V, -40 C T +85 C, unless otherwise noted.)
S A
Parameter Input Offset Voltage
Symbol VOS
Conditions
OP200E Min Typ 35 0.2
Max 100 0.5 2.5 5.0
Min
OP200F Typ Max 80 0.5 0.08 0.3 250 1.5 3.5 70
Min
OP200G Typ Max 110 0.6 0.1 0.5 300 2.0 6.0 10.0
Unit mV mV/C nA nA V/mV V/mV V dB
Average Input Offset Voltage Drift TCVOS Input Offset Current IOS Input Bias Current Large-Signal Voltage Gain Input Voltage Range* Common-Mode Rejection Power Supply Rejection Ratio Output Voltage Swing Supply Current Per Amplifier Capacitive Load Stability
NOTE *Guaranteed by CMR test.
VCM = 0 V VCM = 0 V VO = 10 V RL= 10 kW RL = 2 kW 3000 1500 12 VCM = 12 V VS = 3 V to 18 V RL = 10 kW RL = 2 kW No Load AV = 1 No Oscillations 12 11 115
0.08 03 10000 3200 12.5 130 0.15 12.4 12 600 10 10
IB AVO
2000 1000 12 110 3.2 12 11 775
5000 2500 12.5 130 0.15 12.4 12 600 10 10 775 5.6
2000 1000 12 105
5000 2500 12.5 130 0.3 10.0
IVR CMR PSRR VO
mV/V V V
12 11
12.4 12.2 600 10 10 775
ISY
mA nF nF
-4-
REV. A
OP200
1/2 OP200 V1 20Vp-p @ 10Hz
100 10k
50k 50 1/2 OP200 V2
1/2 OP200 1/2 OP200 eOUT TO SPECTRUM ANALYZER
CHANNEL SEPARATION = 20 LOG
V1 V2/1000
eOUT(nV/ Hz) = 2
eOUT(nV/ Hz)
101
Figure 2. Channel Separation Test Circuit
Figure 3. Noise Test Schematic
ABSOLUTE MAXIMUM RATINGS 1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . 30 V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . Supply Voltage Output Short-Circuit Duration . . . . . . . . . . . . . . Continuous Storage Temperature Range P, S, Z-Package . . . . . . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering, 60 sec) . . . . . . . 300C Junction Temperature (TJ) . . . . . . . . . . . . . -65C to +150C Operating Temperature Range OP200A . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C OP200E, OP200F . . . . . . . . . . . . . . . . . . . . -40C to +85C OP200G . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C Package Type 8-Pin Hermetic DIP (Z) 8-Pin Plastic DIP (P) 16-Pin SOL (S)
JA 2 JC
ORDERING GUIDE
Package TA = 25 C VOS Max ( V) 75 75 150 200 200 CERDIP 8-Pin OP200AZ OP200EZ OP200FZ* OP200GP OP200GS Operating Temperature Range MIL XIND XIND XIND XIND
Plastic
*Not for new design, obsolete April 2002.
Unit C/W C/W C/W
148 96 92
16 37 27
For military processed devices, please refer to the Standard Microcircuit Drawing (SMD) available at www.dscc.dla.mil/programs/milspec/default.asp SMD Part Number 5962-8859301M2A 5962-8859301MPA ADI Equivalent OP200ARCMDA OP200AZMDA
NOTES 1 Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. 2 JA is specified for worst case mounting conditions, i.e., JA is specified for device in socket for CERDIP and P-DIP packages; JA is specified for device soldered to printed circuit board for SOL package.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the OP200 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. A
-5-
OP200 -Typical Performance Characteristics
60
INPUT OFFSET VOLTAGE - V
3
VS = 15V INPUT BIAS CURRENT - nA
CHANGE IN OFFSET VOLTAGE -
TA = 25 C VS = 15V 2
VS = 2 1 0 -1 -2
V
15V
50
40 30 20 10 0 -75 -50 -25 0 25 50 75 TEMPERATURE - C
1
5
0
1
2 3 TIME - Minutes
4
5
100 125
-3 0 25 50 75 -75 -50 -25 TEMPERATURE - C
100 125
TPC 1. Warm-Up Drift
TPC 2. Input Offset Voltage vs. Temperature
TPC 3. Input Bias Current vs. Temperature
300 VS =
INPUT OFFSET CURRENT - pA
1.0
COMMON-MODE REJECTION - dB
140
15V
INPUT BIAS CURRENT - nA
250
TA = 25 C VS = 15V 0.8
120 100 80 60 40 20 0
TA = 25 C VS = 15V
200 150 100 50 0 -75 -50 -25 0 25 50 75 TEMPERATURE - C
0.6
0.4
0.2
100 125
0 -15
-10 -5 0 5 10 COMON-MODE VOLTAGE - V
15
1
10
100 1k FREQUENCY - Hz
10k
100k
TPC 4. Input Offset Current vs. Temperature
TPC 5. Input Bias Current vs. Common-Mode Voltage
TPC 6. Common-Mode Rejection vs. Frequency
100
CURRENT NOISE DENSITY - nV/ Hz
1000
CURRENT NOISE DENSITY - fA/ Hz
TA = 25 C VS = 15V
TA = 25 C VS = 15V
10
1
10 100 FREQUENCY - Hz
1k
100
1
10 100 FREQUENCY - Hz
1k
TPC 7. Voltage Noise Density vs. Frequency
TPC 8. Current Noise Density vs. Frequency
TPC 9. 0.1 to 10Hz Noise
-6-
REV. A
OP200
1.18
1.16 POWER SUPPLY REJECTION - nA
140
TWO AMPLIFIERS VS = 15V
TOTAL SUPPLY CURRENT - mA
1.16
TWO AMPLIFIERS TA = 25 C
SUPPLY CURRENT - mA 1.15
120 100 80 60 40 20 0 0.1 TA = 25 C 1 10 100 1k FREQUENCY - Hz POSITIVE SUPPLY
NEGATIVE SUPPLY
1.14 1.12
1.14
1.13
1.10 1.08 1.06 2 6 10 14 SUPPLY VOLTAGE - V 16
1.12
1.11 -75 -50 -25 0 25 50 75 TEMPERATURE - C
100 125
10k
100k
TPC 10. Total Supply Current vs. Supply Voltage
TPC 11. Total Supply Current vs. Temperature
TPC 12. Power Supply Rejection vs. Temperature
0.7 POWER SUPPLY REJECTION - V/V
6000 VS = 15V RL = 2k
OPEN-LOOP GAIN - dB
140 120 100 80 60 PHASE 40 20 0 -25 0 25 50 75 TEMPERATURE - C 100 125 -20 10 GAIN 90 135 180 0 TA = 25 C VS = 15V
PHASE SHIFT - Degrees
0.6
5000
OPEN-LOOP GAIN - V/mV
-25 0 25 50 75 TEMPERATURE - C 100 125
0.5 0.4
4000 3000
0.3 0.2 0.1 -75 -50
2000 1000 0 -75 -50
100
1k 10k FREQUENCY - Hz
100k
1M
TPC 13. Power Supply Rejection vs. Temperature
TPC 14. Open Loop Gain vs. Temperature
TPC 15. Open Loop Gain and Phase Shift vs. Frequency
140
OUTPUT SWING - V p-p AT 1% Distortion
30 25 TA = 25 C VS = 15V
1
120 100 AV = 1000 AV = 100 AV = 10 40 AV = 1 20 0 10
TA = 25 C VS = 15V
AV = 100 AV = 10
DISTORTION - %
20 15 10
GAIN - dB
0.1
80 60
AV = 1
0.01 TA = 25 C VS = 15V VOUT = 10V p-p RL = 2k
5 0 10
100
1k 10k FREQUENCY - Hz
100k
1M
100
1k 10k FREQUENCY - Hz
100k
0.001 100
1k FREQUENCY - Hz
10k
TPC 16. Closed Loop Gain vs. Frequency
TPC 17. Maximum Output Swing vs. Frequency
TPC 18. Total Harmonic Distortion vs. Frequency
REV. A
-7-
OP200
50 45 40
OVERSHOOT - %
SHORT-CIRCUIT CURRENT - mA
29
150
TA = 25 C VS = 15V FALLING
35 30 25 20 15 10 5 0 0 0.5 1.0 1.5 1.0 1.5 CAPACITIVE LOAD - nF 3.0 RISING
27 26 SINKING 25 24 SOURCING 23 22 0 1 3 2 TIME - Minutes 4 5
CHANNEL SEPARATION - dB
28
TA = 25 C VS = 15V
140
130 120
110
100 90 10
100
1k 10k FREQUENCY - Hz
100k
TPC 19. Overshoot vs. Capacitive Load
TPC 20. Short-Circuit Current vs. Time
TPC 21. Channel Separation vs. Frequency
TPC 22. Large-Signal Transient Response
TPC 23. Small-Signal Transient Response
TPC 24. Small-Signal Transient Response CLOAD = 1 nF
APPLICATIONS INFORMATION
The OP200 is inherently stable at all gains and is capable of driving large capacitive loads without oscillating. Nonetheless, good supply decoupling is highly recommended. Proper supply decoupling reduces problems caused by supply line noise and improves the capacitive load driving capability of the OP200.
APPLICATIONS DUAL LOW-POWER INSTRUMENTATION AMPLIFIER
+15V 3 VIN 5 1/2 OP200AZ 6 20k 5k RG VOUT = 5 + 40000 VIN + VREF RG 5k 7 2 4 -15V 20k 8 1/2 OP200AZ 1 VOUT
A dual instrumentation amplifier that consumes less than 33 mW of power per channel is shown in Figure 4. The linearity of the instrumentation amplifier exceeds 16 bits in gains of 5 to 200 and is better than 14 bits in gains from 200 to 1000. CMRR is above 115 dB (Gain = 1000). Offset voltage drift is typically 0.2 mV/C over the military temperature range which is comparable to the best monolithic instrumentation amplifiers. The bandwidth of the low-power instrumentation amplifier is a function of gain and is shown below: Gain 5 10 100 1000 Bandwidth 150 kHz 67 kHz 7.5 kHz 500 Hz -8-
VREF
Figure 4. Dual Low-Power Instrumentation Amplifier
The output signal is specified with respect to the reference input, which is normally connected to analog ground. The reference input can be used to offset the output from -10 V to +10 V if required.
REV. A
OP200
PRECISION ABSOLUTE VALUE AMPLIFIER PRECISION CURRENT PUMP
The circuit of Figure 5 is a precision absolute value amplifier with an input impedance of 10 MW. The high gain and low TCVOS of the OP200 ensure accurate operation with microvolt input signals. In this circuit, the input always appears as a common-mode signal to the op amps. The CMR of the OP200 exceeds 120 dB, yielding an error of less than 2 ppm.
+15 C2 0.1pF R1 1k 6 1/2 OP200AZ 5 D1 1N4148 R2 2k 7 VOUT R3 1k
Maximum output current of the precision current pump shown in Figure 6 is 10 mA. Voltage compliance is 10 V with 15 V supplies. Output impedance of the current transmitter exceeds 3 MW with linearity better than 16 bits.
R1 10k VIN R2 10k R3 10k 1/2 OP200EZ 3 1 R5 100 +15 8 7 1/2 OP200EZ 6 4 IOUT = VIN RS = VIN = 10mA/V 100 5 IOUT
2
3
8
C1 30pF
D1 1N4148
R4 1k
1/2 1 OP200AZ VIN 2 4 C2 0.1pF
0V < VOUT < 10V
-15
Figure 6. Precision Current Pump
-15
DUAL 12-BIT VOLTAGE OUTPUT DAC
Figure 5. Precision Absolute Value Amplifier
The dual output DAC shown in Figure 7 is capable of providing untrimmed 12-bit accurate operation over the entire military temperature range. Offset voltage, bias current and gain errors of the OP-200 contribute less than 1/lO of an LSB error at 12 bits over the military temperature range.
5V
21 VDD DAC-8222EW 10V REFERENCE VOLTAGE 4 VREFA DAC A 1/2 DAC8212AV RFBA 3 8
IOUTA 2
2
-
1/2 OP200AZ 1 OUTA
3 DAC DATA BUS PINS 6(MSB) - 17(LSB) 23 RFBB 22 VREFB DAC B 1/2 DAC8212AV IOUTB 24 6
+
4 -15V
-
1/2 OP200AZ 7 OUTB
DAC CONTROL
18 DAC A/DAC B 19 CS 20 WR DGND 5
AGND 1
5
+
Figure 7. Dual 12-Bit Voltage Output DAC
REV. A
-9-
OP200
DUAL PRECISION VOLTAGE REFERENCE
+5V -2.5V R2 10k R1 22k D1 1N914 8 1/2 OP-200AZ 3 2 4 6 6 1/2 OP200AZ 5 7 -5V R4 5k R3 10k 2
A dual OP200 and a REF-43, a 2.5 V reference, can be used to build a 2.5 V precision voltage reference. Maximum output current from each reference is 10 mA with load regulation under 25 mV/mA. Line regulation is better than 15 mV/V and output voltage drift is under 20 mV/C. Output voltage noise from 0.1 Hz to 10 Hz is typically 75 mV p-p. R1 and D1 ensure correct start-up.
PROGRAMMABLE HIGH RESOLUTION WINDOW COMPARATOR
REF-43A 4
The programmable window comparator shown in Figure 9 is easily capable of 12-bit accuracy over the full military temperature range. A dual CMOS 12-bit DAC, the DAC-8212, is used in the voltage switching mode to set the upper and lower thresholds (DAC A and DAC B, respectively).
-2.5V
Figure 8. Dual Precision Voltage Reference
VIN 21 VDD
15V
8 10V REFERENCE 2 IOUTA DAC A 1/2 DAC8212AV RREFA 4 R1 10k DAC DATA BUS PINS 6(MSB) - 17(LSB) 3
+
1/2 OP200AZ 1 D1 1N4148 5V R3 10k R4 10k OUTB
2
- +
1/2 OP200AZ 7
TTL OUT Q1 2N2222
-15V 4 R2 10k D2 1N4148
24 IOUTB
DAC B 1/2 DAC8212AV
RREFB 22
5
-
DAC CONTROL SIGNALS
18 DAC A/DAC B 19 CS 20 WR DGND 5 AGND 1
Figure 9. Programmable High Resolution Window Comparator
-10-
REV. A
OP200
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
PIN CONNECTIONS 16-Pin SOIC (S-Suffix)
0.4133 (10.50) 0.3977 (10.00)
16 9
0.2992 (7.60) 0.2914 (7.40)
1 8
0.4193 (10.65) 0.3937 (10.00)
PIN 1
0.050 (1.27) BSC
0.1043 (2.65) 0.0926 (2.35)
0.0291 (0.74) 0.0098 (0.25)
45
0.0118 (0.30) 0.0040 (0.10)
8 0.0192 (0.49) SEATING 0 0.0125 (0.32) 0.0138 (0.35) PLANE 0.0091 (0.23)
0.0500 (1.27) 0.0157 (0.40)
Epoxy MINI-DIP (P-Suffix)
0.430 (10.92) 0.348 (8.84)
8 5
0.280 (7.11) 0.240 (6.10) 0.325 (8.25) 0.300 (7.62) 0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN 0.015 (0.381) 0.008 (0.204) 0.195 (4.95) 0.115 (2.93)
1
4
PIN 1
0.100 (2.54) BSC
0.210 (5.33) MAX 0.160 (4.06) 0.115 (2.93)
0.022 (0.558) 0.070 (1.77) SEATING 0.014 (0.356) 0.045 (1.15) PLANE
8-Pin Hermetic DIP (Z-Suffix)
0.005 (0.13) MIN
8
0.055 (1.4) MAX
5
PIN 1
1 4
0.310 (7.87) 0.220 (5.59)
0.100 (2.54) BSC 0.405 (10.29) MAX 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN 15 0
0.320 (8.13) 0.290 (7.37)
SEATING 0.023 (0.58) 0.070 (1.78) PLANE 0.014 (0.36) 0.030 (0.76)
0.015 (0.38) 0.008 (0.20)
REV. A
-11-
OP200 Revision History
Location Data Sheet changed from REV. 0 to REV. A. Page
Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to PIN CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Edits to PACKAGE TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
C00322-0-4/02(A) PRINTED IN U.S.A.
-12-
REV. A

▲Up To Search▲

Price & Availability of OP200

	To Download OP200 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .